XC6124E744ER-G belongs to the category of voltage regulators.
It is commonly used for voltage regulation in electronic circuits.
XC6124E744ER-G is available in a small SOT-23-5 package.
The essence of XC6124E744ER-G lies in its ability to regulate voltage efficiently and reliably in various electronic applications.
It is typically packaged in reels containing 3000 units per reel.
XC6124E744ER-G has the following pin configuration:
XC6124E744ER-G operates based on the principle of linear voltage regulation. It uses a pass transistor to regulate the output voltage by adjusting the resistance between the input and output terminals. The enable pin allows the user to control the regulator's operation.
XC6124E744ER-G finds applications in various electronic devices, including but not limited to: - Mobile phones - Portable media players - Digital cameras - Wireless communication modules - Battery-powered devices
Some alternative models that can be considered as alternatives to XC6124E744ER-G are: - LM1117-3.3 - LT1761ES5-3.3 - MCP1700-3302E/TO
These models offer similar functionality and characteristics, providing options for different design requirements.
In conclusion, XC6124E744ER-G is a compact and efficient voltage regulator with a wide range of applications. Its high efficiency, low dropout voltage, and built-in protection features make it a reliable choice for voltage regulation in various electronic circuits.
Sure! Here are 10 common questions and answers related to the application of XC6124E744ER-G in technical solutions:
Question: What is XC6124E744ER-G?
- Answer: XC6124E744ER-G is a voltage detector IC (integrated circuit) manufactured by Torex Semiconductor. It is commonly used for monitoring power supply voltages in various electronic devices.
Question: What is the operating voltage range of XC6124E744ER-G?
- Answer: The operating voltage range of XC6124E744ER-G is typically between 0.8V and 6.0V.
Question: How does XC6124E744ER-G work?
- Answer: XC6124E744ER-G works by comparing the input voltage with a fixed reference voltage. When the input voltage falls below or exceeds a certain threshold, it triggers an output signal to indicate the voltage status.
Question: What is the output type of XC6124E744ER-G?
- Answer: XC6124E744ER-G has an open-drain output type, which means it can sink current but cannot source current. It requires an external pull-up resistor to provide the desired output voltage level.
Question: What is the typical quiescent current consumption of XC6124E744ER-G?
- Answer: The typical quiescent current consumption of XC6124E744ER-G is very low, usually around 1.0µA.
Question: Can XC6124E744ER-G be used for undervoltage and overvoltage detection?
- Answer: Yes, XC6124E744ER-G can be used for both undervoltage and overvoltage detection. It has separate thresholds for each condition, allowing it to monitor voltage levels in a wide range.
Question: What is the accuracy of XC6124E744ER-G?
- Answer: The accuracy of XC6124E744ER-G is typically ±1.5% for the detection voltage.
Question: Can XC6124E744ER-G be used in battery-powered applications?
- Answer: Yes, XC6124E744ER-G can be used in battery-powered applications. Its low quiescent current consumption makes it suitable for power-sensitive devices.
Question: Does XC6124E744ER-G have any built-in delay or hysteresis?
- Answer: Yes, XC6124E744ER-G has a built-in delay of approximately 200ms and hysteresis of about 100mV, which helps prevent false triggering due to voltage fluctuations.
Question: What package does XC6124E744ER-G come in?
- Answer: XC6124E744ER-G is available in an SOT-25 package, which is a small surface-mount package with 5 pins.
Please note that the answers provided here are general and may vary depending on the specific datasheet and application requirements.